Junction Box Panel Stainless Steel IP66 for Emergency Lighting
Construction
Gland plate with sealing gasket
14 gauge or 16 gauge stainless steel
The enclosure has metric clearance / plain entry holes as standard. Alternative clearance holes are available provided they are to a recognised standard e.g. BSPP, ET etc. ( Parallel threads only) . Plain entry holes must maintain the following:
a) The plain hole shall be no larger than 0.7mm above the major diameter of the entry thread.
b) The cable gland or stopping plug is secured internally by a locknut, such that the cable gland or stopping plug will not be dislodged by a 7Nm impact.
c) The enclosure should be maintained at IP66 by the use of a suitable sealing washer under the shoulder of the cable gland.
The customer may drill plain entry holes in the enclosure providing they are in accordance with the relevant code of practice and comply with the certification, contact Hawke Technical Sales for more information.
When mixed entries are required on a face, contact Hawke Technical Sales for more information.
All unused entry holes must be fitted with a stopping plug as listed on the enclosure certificate. The stopping plug shall be held in place by a locknut.
Specification
H2/ 2HK Instrument Box
H2/ 2HK instrument Junction box instrumentaion house of junction box in HK series used to measure, detect, monitor, transmit and control industrial processed and systems.
ThisEnclosures is good for flow measurement devices, temperature monitor, transmitters, gas detectors, ph analyzers, pressure gauges, temperature transmitters, oxygen/ combustible gas sensor and this H2/ 2HK instrument/ Device Junction box/ Enclosures is also for gas monitors, level detectors, H2S monitor, transducer, pressure switch.
jual drain breather for Junction Box
All junction box for hazardous need to be installed in the top of an enclosures this drain breather or drain breater as breathers for gas to flow out on the pressured junction box, this drain breather which is mandatory for all explosion proof junction box system.
Should this drain breather installed on the bottom it will permit water to drain from the enclosure continuously to get better result through this drain breather, especially a drain breather is needed for cast iron boxes which can be used for offshore and onshore platform electrical installation, while All drain breathers for indonesia are designed for use in 1/ 2inch.
Jual Distribution Equipment Panel – Circuit Breaker Enclosure
• This Junction Box Panel are to provide overcurrent and short circuit protection of service entrance, feeder or branch circuits, lighting, heating, appliance and motor circuits • To provide line disconnect means
Features
• Copper-free, cast aluminum construction ( less than 4/ 10 of 1% ) • High strength, lighter in weight, corrosion resistant
• Hinged Cover is standard .Meets the latest NEC/ CEC wire bending requirements for circuit breaker enclosures
• Gasketed Flange, Nitrile ( BUNA-N) “ O” ring gasket is located inside cover bolt circle to prevent water seeping into enclosure
• Quick Release, Captivated Cover, Bolts of 316 Grade Stainless Steel Triple lead bolts require only 3-1/ 2 turns to disengage
Material/ Finish
• Enclosure: Copper-free, cast aluminum ( less than 4/ 10 of 1% ) , Cover Bolts: 316 grade stainless steel, Mounting Pan: Sheet aluminum, Handle Mechanism: Cast aluminum with stainless steel shaft and hardware, Hinges: Aluminum with stainless steel hardware, Aluminum lacquer paint finish is standard, with special epoxy finish available. Ductile Mounting Lugs. Lugs are made of ductile aluminum alloy to adjust to irregular mounting surfaces without damage to enclosure, Universal Mounting Pan. Sheet aluminum pan is pre-drilled to facilitate easy field installation of major circuit breaker brands, Provisions for grounding supplied as standard, Conduit Openings Supplied. Standard conduit openings include power conduit top and bottom and a plugged opening suitable for field installation of drain and breather Special conduit openings can be supplied at factory, or can be field installed
Non-fused Disconnect Switch Box
The PRISM® B7 Series from Killark of non-fused disconnect switches Box are used:
• In locations made hazardous due to the, presence of flammable gasses or vapors or ignitable dusts, fibers and flyings.
• Outdoors or indoors in damp, wet and dirty locations, or in areas where frequent washdowns, heavy rain or water spray
routinely occurs. Use as motor circuit disconnect. PRISM® enclosures universal design accomodates the following manufacturers switches as standard:
• Advance Controls 14046 Series Allen-Bradley 194E Series ( B7NFD1 only) , ABB OT Series, Cutler-Hammer C362N Series Sprecher + Schuh LA7 Series, Ferraz Shawmut LBS Series,dvance Controls © Advance Controls Inc.Allen-Bradley © Rockwell Automation ABB © Tne ABB Group
